Paramèt debaz nan laprès idwolik
Paramèt debaz yo se done teknik debaz yo nan laprès idwolik la, ki detèmine dapre itilizasyon teknolojik ak kalite estrikti nan laprès idwolik la. Li reflete kapasite travay la ak karakteristik laprès idwolik la, epi tou li fondamantalman detèmine gwosè deskripsyon an ak pwa an jeneral brit nan laprès idwolik la. Paramèt debaz yo chwazi pa itilizatè a. Prensipal baz pou achte. Se konsa, sa ki paramèt debaz yo nan laprès idwolik la? Ki jan yo konprann epi chwazi paramèt yo nan laprès idwolik la? Jodi a, mwen pral regle paramèt debaz yo nan laprès idwolik komen twa-travès kat-kolòn pou ou.
1. Fòs nominal (KN)
The nominal force is generally the main parameter of the hydraulic press, which reflects the working capacity of the hydraulic press. The nominal force is the maximum working pressure that the hydraulic press can nominally issue, and is numerically equal to the product of the maximum liquid pressure and the total area of the working plunger (piston radius) R²πpressure gauge value (system pressure)
Note: 1MPa≈100N
Take 60T calculation as an example: cylinder diameter φ180mm system pressure 25MPa (for high pressure)
90903.1425÷10000 (unit conversion)
2. Maksimòm headroom (wotè ouvèti)
The maximum clearance distance refers to the distance from the upper surface of the table to the lower surface of the movable beam when the movable beam stops at the upper limit position. The maximum clearance distance reflects the size of the working space of the hydraulic press in the height direction. It should be determined by process factors such as the height of the mold and the corresponding backing plate, the size of the working stroke, and the size of the space required for placing the blank and taking out the workpiece. The maximum clearance has a great influence on the overall height of the hydraulic press, the length of the column, the stability of the hydraulic press body and the height of the installation workshop. The maximum clearance distance of the single-arm hydraulic press is the distance from the lower plane of the indenter to the upper surface of the table.
3. Maksimòm kou
The maximum stroke refers to the distance from the lower plane of the column guide sleeve of the movable beam to the upper plane of the column travel limit sleeve when the movable beam is at the upper limit position, that is, the maximum distance that the movable beam can move. The maximum stroke should be determined according to the required maximum working stroke during the workpiece forming process.
4. Gwosè tab (longè lajè)
The workbench is generally the place where the mold is placed. The size of the worktable refers to the effective size that can be used on the worktable, and the size of the worktable depends on the plane size of the mold and the arrangement of the process.
5. Pwofondè gòj (yon sèl -kolòn idwolik laprès)
Refers to the distance from the center of the single-column hydraulic press head to the inner surface of the frame.
6. Retounen fòs
The return force refers to the weight of the movable part, the force required for the return process (such as the draft force, the lifting force of the chopping knife), etc.
7. Vitès mouvman gwo bout bwa mobil (vitès koulis): li ka divize an vitès konjesyon serebral k ap travay, konjesyon serebral san fè anyen konsa (konjesyon serebral likid ranpli) vitès ak vitès konjesyon serebral retounen.
The idle travel and return travel can generally be higher to improve productivity, but too fast will cause shock and vibration when stopping or reversing.
Gen twa kalite vitès:
⑴Constant speed (eternal speed): rising speed, falling speed (using electro-hydraulic reversing valve)
⑵Differential: ①Fast down, slow back ②Slow down, fast back, idle descending, pressing, and returning (with cartridge valve) ③Up and down equal velocity
(3) Vit (sistèm ranpli likid): Li se tou fè espre ekipe ak yon vitès -ogmante silenn, olye pou yo konte sou pwa pwòp li yo gout;
8. Fòs ekspilsyon nominal ak kou ekspilsyon
The function of the ejector cylinder is to eject or stretch, and the power and stroke safety of the ejector are determined by the process requirements;
9. Y27 moun ki pa marye -aksyon dra s' idwolik yo opere Sur tou bezwen konnen idwolik yo opere ansman twal gaz fòs ak idwolik yo opere ansman twal gaz paramèt.
10. Y28 doub -aksyon fèy desen idwolik pou laprès la bezwen tou konnen paramèt fòs desen an, fòs detantè vid la, kous kurseur desen an, kou detantè vid la, wotè ouvèti a. desen kurseur, ak wotè ouvèti detantè a vid.
11. Si yon sèl -kolòn pou laprès idwolik la se yon kalite chuck oswa yon estrikti kurseur anwo (tip peze plak), si li nesesè pou korije tab travay la, elatriye.
12. Sekans aksyon (pwosesis aksyon) Kliyan an bay sekans pwosesis peze ak kondisyon pwosesis (kondisyon pwosesis).






